Analysis of T-Shirt Product Quality Control to Minimize Defects Using Fault Tree Analysis (FTA) and Failure Mode and Effects Analysis (FMEA) at CV Dwiputra Ihwa

Rifal Choerul  Harisin; Rizky Fajar Ramdhani; Akhsani Nur  Amalia

doi:10.54783/influencejournal.v8i2.353

Authors

Rifal Choerul Harisin Sekolah Tinggi Teknologi Wastukancana, Purwakarta, Indonesia
Rizky Fajar Ramdhani Sekolah Tinggi Teknologi Wastukancana, Purwakarta, Indonesia
Akhsani Nur Amalia Sekolah Tinggi Teknologi Wastukancana, Purwakarta, Indonesia

DOI:

https://doi.org/10.54783/influencejournal.v8i2.353

Keywords:

Quality Control, Defective Products, Fault Tree Analysis, Failure Mode and Effect Analysis, Risk Priority Number.

Abstract

CV Dwiputra Ihwa is a company that operates in the garment industry, specifically producing T-shirts based on special orders or in large quantities. From June 2025 to May 2026, the percentage of defective products was 7.6% out of a total production of 18,478 units. This situation leads to more rework, waste of raw materials, and lower production efficiency. This study aims to find out which type of defect is most common, look into why these defects happen, and figure out what improvements should be done first to make the T-shirt product better. The study uses a descriptive method with a qualitative approach through a case study. Data was collected through observation, interviews, and document study, then analyzed using Pareto Diagram, Fault Tree Analysis, and Failure Mode and Effect Analysis. The Pareto chart analysis shows that stitching defects (43%) and inaccurate screen-printing defects (37%) are the two main types of defects, contributing about 80% of all defective products. The FTA analysis shows that the second type of defect is caused by a combination of human factors, methods, materials, and machines (4M), with human factors and methods being the most significant causes. The FMEA analysis results show that the Risk Priority Number (RPN) ranges from 30 to 252, with the highest risk cause being overly high production targets (RPN = 252). Based on the research results, it can be concluded that using Pareto Diagram, FTA, and FMEA is effective in identifying types of defects, analyzing root causes, and determining priorities for improvement, which helps support the enhancement of the quality of T-shirts produced by CV Dwiputra Ihwa.

References

Alifka, K. P., & Apriliani, F. (2024). Analisis Pengendalian Kualitas Produk Menggunakan Metode Statistical Process Control (SPC) dan Failure Mode and Effect Analysis (FMEA). Factory Jurnal Industri, Manajemen dan Rekayasa Sistem Industri, 2(3), 97–118. https://doi.org/10.56211/factory.v2i3.486

Anwar, S., Ulum, R. B., & Widarman, A. (2023). Analisis Pengendalian Kualitas Dengan Menggunakan Metode Fta (Fault Tree Analysis) Dan Fmea (Failure Mode and Effect Analysis) Pada Proses Produksi Pita Cukai Berperekat di Perusahaan Percetakan Dokumen Sekuriti Karawang. Jurnal Ilmiah Multidisiplin, 2(04), 114-128.

Arif, R., & Gunawan, A. G. (2023). Diagram Pareto dan Diagram Fishbone: Penyebab yang mempengaruhi Keterlambatan Pengadaan Barang di Perusahaan Industri Petrochemicals Cilegon Periode 2020-2022. Jurnal Riset Bisnis dan Manajemen Tirtayasa, 7(1), 1-10.

Gupta, R. (2023). Failure Mode and Effects Analysis of PCB for Quality Control Process. Mapan-Journal of Metrology Society of India, 38(2), 547–556. https://doi.org/10.1007/s12647-022-00619-5

Hamdani, D., Fata, A. F. I., & Iskandar, H. (2026). Analisis Pengendalian Kualitas Produk T-Shirt Menggunakan Metode Fault Tree Analysis & Failure Mode and Effetcs Analysis Pada PT. XYZ. Journal Industrial Engineering and Management (JUST-ME), 7(01), 17-26.

Hardianto, R. D. Nuriyanto. (2023). Analisis Penyebab Reject Produk Paving Block Dengan Pendekatan Metode FMEA dan FTA. Jurnal Cakrawala Ilmiah, 2(12), 4635-4648.

Krisnaningsih, E., Gautama, P., & Syams, M. F. K. (2021). Usulan perbaikan kualitas dengan menggunakan metode FTA dan FMEA. Jurnal Industri dan Teknologi Terpadu, 4(1), 41-54.

Nurwulan, N. R., & Veronica, W. A. (2020). Implementation of Failure Mode and Effect Analysis and Fault Tree Analysis in Paper Mill: A Case Study. Jurnal Rekayasa Sistem Industri, 9(3), 171–176. https://doi.org/10.26593/jrsi.v9i3.4059.171-176

Putri, A. S., & Utami, R. I. (2023). Analisis Pengendalian Kualitas Cacat Rework Dengan Metode FMEA Pada Intimates Wear Product. Jurnal Industri dan Teknologi Samawa, 4(1), 15-23.

Sjarifudin, D., Kurnia, H., Nuryono, A., & Tambunan, E. B. M. (2023). Hazard Identification Risk Assessment and Determining Control (HIRADC) Method for Shoe Cutting Dies Production. Jurnal Sistem Teknik Industri, 25(2), 322–333. https://doi.org/10.32734/jsti.v25i2.12186

Sugarindra, M., Tyas, S. W., Parkhan, A., & Fauza, E. (2025). Quality Control of Regular Slotted Containers Production Process Using Failure Mode and Effect Analysis and Fault Tree Analysis. Jurnal Disprotek, 16(2), 127-132.

Wicaksono, A., Priyana, E. D., & Nugroho, Y. P. (2023). Analisis Pengendalian Kualitas Menggunakan Metode Failure Mode and Effects Analysis (FMEA) Pada Pompa Sentrifugal Di PT. X. Jurnal Teknik Industri, 9(1), 177-185.

Yunita, D. R., Ulum, R. B., & Wibowo, P. A. (2025). Analisis Pengendalian Kualitas dengan Menggunakan Metode Fault Tree Analysis (FTA) dan Failure Mode and Effect Analysis (FMEA) untuk Mengurangi Produk Cacat Klem Accu di IKM Geulis Automotif. Jurnal Teknik Industri Terintegrasi, 8(3), 3342–3353. https://doi.org/10.31004/jutin.v8i3.48228